Commit bdcc9de0 authored by Alexandre Berge's avatar Alexandre Berge
Browse files

Merge branch 'ericsson-converting-dl-notes-into-ul-notes' into 'Rel-19' 

Converting various "DL notes" into "UL Notes"

See merge request ran4/specifications/38.101/common!2
parents 991647ef 347e1c97

jsonSchemas/BandCombinationsCarrierAggregation.json

+8 −8
Original line number Diff line number Diff line
@@ -51,6 +51,10 @@ 
                      "description": "Limited to operation at 3450-3550 MHz and 3700-3980 MHz.",

                      "type": "boolean"

                    },

                    "n5A-n8A_restrictions": {

                      "description": "When UL CA_n5A-n8A is supported, some restrictions may be needed to avoid simultaneous n5DL and n8 UL during UL CA_n5A-n8A with DL CA_n5A-n8A configuration. The UE and/or NW behaviors are not specified in the 3GPP specifications when there is a conflict between n5DL and n8UL including dynamic scheduling, semi-static signals and unspecified transitions between n5DL and n8UL.",

                      "type": "boolean"

                    },

                    "n26_DualPA": {

                      "description": "Unless otherwise stated, only RF requirements for dual PA architecture are applicable for UL CA_n26(2A) and UE shall indicate the dualPA-Architecture for UL CA_n26(2A).",

                      "type": "boolean"
@@ -83,6 +87,10 @@ 
                      "description": "In Rel-18 maximum aggregated uplink BW is limited to 800 MHz.",

                      "type": "boolean"

                    },

                    "ul_n5": {

                      "description": "Uplink is only in n5 for CA_n5-n8.",

                      "type": "boolean"

                    },

                    "ul_n26_opt": {

                      "description": "For UEs only supporting DL CA_n26-n28, uplink support in band n26 is optional, if the UE supports CA_n26-n28 UL configuration, it should also support UL in band n26 and n28.",

                      "type": "boolean"
@@ -210,10 +218,6 @@ 
          "description": "Applicable only for UEs which indicate support of low NR band carrier aggregation via switching supportedLowBandSwitching-r19 for this NR CA configuration.",

          "type": "boolean"

        },

        "n5A-n8A_restrictions": {

          "description": "When UL CA_n5A-n8A is supported, some restrictions may be needed to avoid simultaneous n5DL and n8 UL during UL CA_n5A-n8A with DL CA_n5A-n8A configuration. The UE and/or NW behaviors are not specified in the 3GPP specifications when there is a conflict between n5DL and n8UL including dynamic scheduling, semi-static signals and unspecified transitions between n5DL and n8UL.",

          "type": "boolean"

        },

        "n7_n38": {

          "description": "For a band combination which include band n7 and n38 simultaneously, carriers in band n7 and n38 can only be configured as downlink carriers. Power imbalance between downlink carriers on Band n7 and Band n38 is assumed to be within 6dB.",

          "type": "boolean"
@@ -250,10 +254,6 @@ 
          "description": "In Rel-18 maximum aggregated downlink BW is limited to 1600 MHz.",

          "type": "boolean"

        },

        "ul_n5": {

          "description": "Uplink is only in n5 for CA_n5-n8.",

          "type": "boolean"

        },

        "ul_n28": {

          "description": "UL carrier shall be supported in Band n28 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

          "type": "boolean"

jsonSchemas/BandCombinationsDualConnectivity.json

+38 −34
Original line number Diff line number Diff line
@@ -49,6 +49,10 @@ 
                "description": "For UE(s) supporting dynamic power sharing it is mandatory to do dual simultaneous UL. For UE(s) not supporting dynamic power sharing single UL is allowed. Uplink DC_(n)71AA is not applicable to BCS2.",

                "type": "boolean"

              },

              "pc2": {

                "description": "Minimum requirements for PC2 are applicable for this uplink EN-DC configuration in this downlink/uplink EN-DC configuration.",

                "type": "boolean"

              },

              "pc2_1tx+1tx": {

                "description": "Minimum requirements for PC2 are applicable for this uplink EN-DC configuration in this downlink/uplink EN-DC configuration with 1Tx antenna connector in each band.",

                "type": "boolean"
@@ -62,8 +66,37 @@ 
                "type": "boolean"

              },

              "pc1.5_Table6.2B.1.1-1": {

                "description": "The PC2 Uplink EN-DC configuration supported in Table 6.2B.1.1-1 is applicable to the same EN-DC configuration.",

                "description": "The PC1.5 Uplink EN-DC configuration supported in Table 6.2B.1.1-1 is applicable to the same EN-DC configuration.",

                "type": "boolean"

              },

              "B1orB28Only": {

                "description": "UL carrier shall be supported in Band 1 or band 28 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

                "type": "boolean"

              },

              "B2orB66Only": {

                "description": "UL carrier shall be supported in Band 2 or band 66 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

                "type": "boolean"

              },

              "B3orB28Only": {

                "description": "UL carrier shall be supported in Band 3 or band 28 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

                "type": "boolean"

              },

              "DC_2_n2_RESSENS": {

                "description": "The downlink DC_2_n2 RESSENS requirements only apply when the band n2 downlink carrier is configured closer to the uplink operating band than the E-UTRA Band 2 downlink carrier.",

                "type": "boolean"

              },

              "fwa4Ant": {

                "description": "The implementation with 4 antennas is targeted for FWA form factor for this band combination.",

                "type": "boolean"

              },

              "n71AA_Uplink_BCS2": {

                "description": "Uplink DC_(n)71AA is not applicable to BCS2."

              },

              "presentRelease": {

                "description": "Uplink EN-DC configurations are the configurations supported by the present release of specifications. WARNING: This should not be used in any BC."

              },

              "undefined": {

                "description": "WARNING: This footnote is used in some BCs but undefined in the specification."

              }

            }

          }
@@ -107,6 +140,10 @@ 
          "description": "The minimum requirements apply only when there is non-simultaneous Rx/Tx operation between E-UTRA and NR carriers. This restriction applies also for these carriers when applicable EN-DC configuration is part of a higher order EN-DC configuration.",

          "type": "boolean"

        },

        "nonSimRxTx": {

          "description": "The minimum requirements apply only when there is non-simultaneous Rx/Tx operation between E-UTRA and NR carriers. This restriction applies also for these carriers when applicable EN-DC configuration is part of a higher order EN-DC configuration.",

          "type": "boolean"

        },

        "B42B48_n77n78": {

          "description": "If a UE does not indicate interBandMRDC-WithOverlapDL-Bands-r16 or a UE indicates both interBandMRDC-WithOverlapDL-Bands-r16 and requirementTypeIndication-r18 and IE nonCollocatedTypeMRDC is provided, the minimum requirements for intra-band non-contiguous EN-DC apply for the Band 42/48 and Band n77/n78 combination. If a UE does not indicate interBandMRDC-WithOverlapDL-Bands-r16 or a UE indicates both interBandMRDC-WithOverlapDL-Bands-r16 and requirementTypeIndication-r18 and IE nonCollocatedTypeMRDC is provided and UE indicates interBandContiguousMRDC, the minimum requirements for intra-band contiguous EN-DC also apply in addtion to intra-band non-contiguous EN-DC. The intra-band requirements also apply for these carriers when applicable EN-DC configuration is a subset of a higher order EN-DC configuration.",

          "type": "boolean"
@@ -147,10 +184,6 @@ 
          "description": "Simultaneous Rx/Tx capability does not apply for UEs supporting band 42 with a n77 implementation only. Same restrictions are applied to related higher order configurations.",

          "type": "boolean"

        },

        "fwa4Ant": {

          "description": "The implementation with 4 antennas is targeted for FWA form factor for this band combination.",

          "type": "boolean"

        },

        "noFallbackWithoutB2": {

          "description": "The combination is not used alone as fallback mode of other band combinations in which UL in Band 2 is not used.",

          "type": "boolean"
@@ -183,10 +216,6 @@ 
          "description": "The frequency range in band 42 is restricted for this band combination to 3440 - 3520 MHz.",

          "type": "boolean"

        },

        "pc2": {

          "description": "Minimum requirements for PC2 are applicable for this uplink EN-DC configuration in this downlink/uplink EN-DC configuration.",

          "type": "boolean"

        },

        "noInterBandMRDC": {

          "description": "For UEs not indicating interBandMRDC-WithOverlapDL-Bands-r16, the minimum requirements for intra-band non-contiguous EN-DC apply for the Band 42/48 and Band n77/n78 combination and for the Band 2 and Band n25 combinations. For UEs not indicating interBandMRDC-WithOverlapDL-Bands-r16, when UE capability interBandContiguousMRDC is indicated, the minimum requirements for intra-band-contiguous EN-DC also should be met in addtion to intra-band non-contiguous EN-DC.",

          "type": "boolean"
@@ -203,10 +232,6 @@ 
          "description": "For UEs not indicating interBandMRDC-WithOverlapDL-Bands-r16, the minimum requirements apply for synchronized DL carriers with a maximum receive time difference ≤ 3 usec between overlapping or partially overlapping DL bands contained in different cell groups.",

          "type": "boolean"

        },

        "DC_2_n2_RESSENS": {

          "description": "The downlink DC_2_n2 RESSENS requirements only apply when the band n2 downlink carrier is configured closer to the uplink operating band than the E-UTRA Band 2 downlink carrier.",

          "type": "boolean"

        },

        "nonSimuRxTx_n77n79": {

          "description": "The minimum requirements apply only when there is non-simultaneous Rx/Tx operation between n77-n79 NR carriers. This restriction applies also for these carriers when applicable EN-DC configuration is part of a higher order configuration.",

          "type": "boolean"
@@ -219,10 +244,6 @@ 
          "description": "Only applicable for UE supporting inter-band carrier aggregation without simultaneous Rx/Tx.",

          "type": "boolean"

        },

        "B2orB66Only": {

          "description": "UL carrier shall be supported in Band 2 or band 66 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

          "type": "boolean"

        },

        "noFallbackWithoutB42": {

          "description": "The combination is not used alone as fall back mode of other band combinations in which UL in Band 42 is not used.",

          "type": "boolean"
@@ -243,14 +264,6 @@ 
          "description": "Band 7 and Band n38 are restricted as DL Scell. Power imbalance between downlink carriers on Band 7 and Band 38  is assumed to be within 6dB.",

          "type": "boolean"

        },

        "B1orB28Only": {

          "description": "UL carrier shall be supported in Band 1 or band 28 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

          "type": "boolean"

        },

        "B3orB28Only": {

          "description": "UL carrier shall be supported in Band 3 or band 28 only. Power imbalance between downlink carriers on Band 7 and Band 38 is assumed to be within 6dB.",

          "type": "boolean"

        },

        "noInterBandMRDC_B42_n77n78": {

          "description": "For UEs not indicating interBandMRDC-WithOverlapDL-Bands-r16, the minimum requirements for intra-band non-contiguous EN-DC apply for the Band 42 and Band n77/n78 combination. For UEs not indicating interBandMRDC-WithOverlapDL-Bands-r16, when UE capability interBandContiguousMRDC is indicated, the minimum requirements for intra-band-contiguous EN-DC also should be met in addtion to intra-band non-contiguous EN-DC.",

          "type": "boolean"
@@ -258,15 +271,6 @@ 
        "NA": {

          "description": "Not Available (defined an used in Table 5.5B.4.2-1)"

        },

        "n71AA_Uplink_BCS2": {

          "description": "Uplink DC_(n)71AA is not applicable to BCS2."

        },

        "presentRelease": {

          "description": "Uplink EN-DC configurations are the configurations supported by the present release of specifications. WARNING: This shoudl not be used in any BC."

        },

        "undefined": {

          "description": "WARNING: This footnote is used in some BCs but undefined in the specification."

        },

        "void": {

          "description": "Void (might be used for some BCs but has no valid meaning anymore)"

        }